You have come to the correct location if you want to install a shower curtain rod.

Any homeowner can complete the easy task of installing a shower curtain rod. A well-installed shower curtain rod can give a bathroom a touch of refinement.

Installations of tension rods and permanent rods will be covered today. A few related subjects will also be covered in this tutorial, such as:

• How High a Tension Adjustable Shower Curtain Rod Should Be Installed
• How to Put in a Shower Curtain Rod Permanently
• The steps for mounting a shower curtain rod in drywall
• Where to Mount a Rod for a Shower Curtain
• How to Mount a Curtain Rod in a Shower on Tile

This job should be completed in less than an hour overall. For simple and easy steps, please continue reading.

Required Equipment and Supplies

As with any home repair project, you start by gathering all the necessary supplies and tools. The specific components required will vary based on the installation method. The following materials may be required:

Tension rod rod with support brackets: 

• drill and drill bit
• Wall Hangings
• Measurement tape
• Shower Curtain Hooks with Stud Finder
• Pencil Shower Curtain Standard

Particularly if you are installing a tension rod, you might not require all of these supplies and instruments.

The Right Location for a Shower Rod

“Where do you put a shower curtain rod?” may be the first thing on your mind.

You’ll need the shower curtain you plan to use in order to respond to that question.

To start, place your shower curtain up against the wall and mark the location of the curtain’s bottom. Generally speaking, the bottom hem should be around five inches below the bathtub’s top.

Make the necessary adjustments to the shower curtain and use a pencil to mark the wall above the top of the curtain. Measure the other side using the same procedure. You will install your shower curtain rod in these areas.

The Shower Curtain Rod Installation

You must choose the sort of rod you want to use before you can install a shower curtain rod. A tension rod can be used on tile and stainless steel, and it has the easiest installation procedure of any type of rod. If not, a rod with support brackets is typical, particularly when using drywall.

The next step is to determine the height at which your rod should be positioned. At last, you are able to start the installation!

Setting Up and Modifying a Tension Rod

The process of installing a tension rod is easy. To begin with, shorten the tension rod by approximately one inch compared to the span of the installation site.

Place one end of the rod against the previously formed mark on the wall.

To make the rod stretch and fill the space, turn it counter-clockwise. Turn it again until it’s tight and strong.

Simply twist the tension rod clockwise until it releases to make adjustments or remove it. The installation is finished after the pole is in position and the shower curtain is fastened with shower curtain rings!

Rod Installation Using Support Brackets

It is not difficult to install a wall-mounted rod. To start, locate any wood studs behind the installation site you previously marked using a stud finder.

If so, you can screw each support bracket straight into the wall using the hardware that comes with it. You are done once you’ve put in each support bracket and the shower rod!

In the event that there are no studs, the brackets can be supported with drywall anchors. For your drywall anchors, use a bracket as a template to drill holes beforehand. The plastic anchors can then be inserted into the wall.

You can now screw in the brackets and take use of the strong support that the anchors offer.

After finishing the opposite side, repeat these steps and place your rod into the support brackets. You may now hang your shower curtain by using shower curtain rings.

How to Mount a Shower Curtain Rod That Is Curved

Installing a curved shower curtain rod is necessary if your shower is curved. Fortunately, the procedure is much the same as for a regular rod and bracket.

While some curved rods can be adjusted, others have a set length. Standard six-foot lengths are common for fixed length rods, though they can be shortened upon request. Make sure you order the appropriate length of rod after measuring the span.

The installation height of the curved shower curtain rod will remain the same as it did with the earlier installation techniques.

Installing the support brackets should start with the same steps as installing a regular rod. Should you need to utilize anchors, pre-drill the holes for the anchors using the support bracket as a template. After that, screw in your support brackets and insert the anchors into the holes.

You can now fasten the curved rod after installing your support brackets. The manufacturer’s instructions and documentation will specify the precise attaching procedure. After installation, finish the project by attaching the shower curtain and shower rings!

Shower Curtain Rod Installation on Ceramic Tile

The best way to install a shower curtain rod on tile is to use a tension rod. The tile won’t be harmed in any way by this easy installation method.

In this case, installing a permanent rod installation would not be advised.

Where to Get Rods for Shower Curtains?

BuyRailings.com offers premium shower curtain rods, so you’re covered there. We supply a large selection of railings and rods, including shower rod systems that are straight and curved.